WHR Switcher

The WHR Switcher is two tools in one. Switch between pulling or cleaning without removing the nozzle from the pipe. When the pump is idled down and brought back to pressure, the tool will switch the water flow between two different sets of jets.

The WHR Switcher features the same technology as the WGR Switcher for 3/4" inlets.

Features

  • Eliminates extra runs needed to swap nozzles, saving water and time
  • Excellent for longer runs, climbing hills, going against the flow and flushing large amounts of material without affecting residential infrastructure
  • Run more jobs with one tank of water
  • Switch to pulling jets for maximum thrust
  • Switch to cleaning jets maximize power for cutting roots annd clearing debris
Contact Us for Availability
Tool Family Warthog Switcher
Tool Model WHR Switcher
Pipe Size 6-18 in. 152-457 cm
Pressure Range 1500–8k psi 100–550 bar
Flow Range 14-50 gpm 60-190 l/min
Flow Rating 2.6 Cv
Inlet Connection 3/4 NPT or BSPP
Nozzle Ports 5 x 1/8 NPT
Diameter 3.625 in. 92 mm
Length 8.26 in. 210 mm
Weight 7.48 lb 3.4 kg
Warthog Switcher video

Switcher Overview

The following kits are available:

Click to view kit contents

  • 1 x BJ 048-M Visc Fluid, 6oz
  • 1 x BJ 062-S Antiseize, 2g
  • 1 x GP 049 Grease Syringe
  • 2 x GSS 625-20-25CU Set Screw
  • 2 x MJ 008 Nut O-Ring
  • 1 x SC212 007 Front Bearing
  • 2 x WHR 006 Outer Shaft Seal
  • 1 x WHR 009 Rear Bearing
  • 2 x WHR 010 Inner Shaft Seal
  • 2 x WHR 011 Seal Spacer
  • 2 x WHR 050 O-Ring
  • 1 x WHR 076 Weep Seal O-Ring
  • 4 x WHR 030 Torx Screws
  • 1 x WS 210 O-Ring
  • 1 x BJ 062-S Antiseize, 2g
  • 2 x WHR 050 O-Ring
  • 2 x WHR 052 HP Wave Spring
  • 1 x WHR 058 HP Shaft Seal
  • 1 x WHR 059 HP Nut Seal
  • 2 x BJ 026 Port Plug
  • 1 x BJ 048-M Visc Fluid, 6oz
  • 1 x BJ 062-S Antiseize, 2g
  • 1 x GP 025-P2SS Hex Plug
  • 1 x GP 049 Grease Syringe
  • 2 x GSS 625-20-25CU Set Screw
  • 2 x MJ 008 Nut O-Ring
  • 1 x SC212 007 Front Bearing
  • 2 x WHR 006 Shaft Seal – Outer
  • 1 x WHR 009 Rear Bearing
  • 2 x WHR 010 Shaft Seal – Inner
  • 2 x WHR 011 Seal Spacer
  • 1 x WHR 014 Bearing Wave Spring
  • 4 x WHR 030 Torx Screws
  • 2 x WHR 050 O-Ring
  • 2 x WHR 052 HP Wave Spring
  • 1 x WHR 058 HP Shaft Seal
  • 1 x WHR 059 HP Nut Seal
  • 1 x WHR 076 Weep Seal O-Ring
  • 1 x WS 210 O-Ring
  • 1 x WGRA 180 Torx L-Wrench
  • 1 x BA 481 Bearing Removal Tool
  • 1 x WGR 180 Torx L-Wrench
  • 1 x WGR 181 Removal Press Tube
  • 1 x WGR 182 Installation Press Tube
  • 1 x WGR 183 Hex Tool
  • 1 x WGR 184 HP Seal Install Tool
  • 1 x WGR 186 HP Seal Puller
  • 1 x WGR 187 HP Seal Puller Pin

Switch between two sets of jets right inside the pipe

The WGR Switcher does the job of two tools in one — switch between pulling and cleaning mode without changing nozzles.